B8ta; B550 Motherboard Lineup; ASUS From the Inside; Rank Up with ROG Elite Rewards; Rate Your Gear; ASUS BR1100; 4k, 144Hz with DSC Technology. New Method:https://www.youtube.com/watch?v=c9qAq6MeJdQ.

1. Cirrus Logic Sound Cards & Media Devices Driver Download For Windows 7
2. Cirrus Logic Sound Cards & Media Devices Driver Download For Windows 8
3. Cirrus Logic Sound Cards & Media Devices Driver Download For Windows 10
4. Cirrus Logic Sound Cards & Media Devices Driver Download For Windows 8.1

90 drivers total Last updated: Mar 7th 2017, 09:28 GMT RSS Feed

sort by:

The sound is fine when in Apple mode, but when booted up in Windows 10, all seems to be fine except that there is no sound from the internal speakers. The i-Mac uses a cirrus sound chip, we can't find a Windows driver for it anywhere on line. Windows says that the sound is working correctly, but still no sound! We do not manufacture graphics cards, sound cards or modems. And mine sound card is CirrusLogic CS4206A (AB13) And woow you have inputs & outputs category:O.

Cirrus Logic Sound Cards & Media Devices Driver Download For Windows 7

Cirrus Logic Sound Cards & Media Devices Driver Download For Windows 8

I've been working on a reworked driver, based on Linux kernel 4.9,that doesn't require out-of-tree patches to the upstream kernel modules.This driver also adds a lot of new features and bugfixes like fixedmicbias setting on LineIn, exposing of WM8804 status and AES bitsas ALSA controls and configurable minimum/maximum samplerate limits.

Installation

The driver is included in official RPi and Raspbian kernels since early 2017.Make sure your system is up to date and you are running RPi kernel 4.9.12 or newer.

Source code is available from the usual placehttps://github.com/raspberrypi/linux.

Please note: If you've been compiling from source please switch to theofficial RPi kernel source. I'm no longer maintaining the code in my developmenttreecirrus-ng-4.9.y

Configuration for kernel 4.9 and newer

Enable the driver

Add the following line to /boot/config.txt to enablethe Cirrus Logic card driver

Note: MMAP support is already enabled by default in kernel 4.9, you nolonger need to add the i2s-mmap overlay.

Setup module dependencies

The cirrus driver requires some manually defined module dependencies,if you fail to add them the driver won't load properly.

Create a file /etc/modprobe.d/cirrus.conf with thefollowing content:

Download and install 'usecase' mixer scripts

Download cirrus-ng-scripts.tgzand extract it for example in /home/pi/bin.

Note: If you had installed the older usecase scripts for kernel 4.4 you needto remove them.

You have to start the appropriate scripts before you can usethe card. For example:

Additional configuration steps

Disable RPi on-board audio device snd-bcm2835

On Raspbian the RPi on-board audio device snd-bcm2835 isenabled by default. When you run aplay -l you'll seetwo cards, the Cirrus card sndrpiwsp and the on-boardcard bcm2835.

If you don't need on-board audio you can disable it by removing(or commenting out) the dtparam=audio=on line from /boot/config.txt.

Optionally: use fixed card number

Cirrus Logic Sound Cards & Media Devices Driver Download For Windows 10

If you don't want to disable snd-bcm2835 or if you also havean USB audio device connected you might notice thatthe card numbers under which the drivers register will change.Sometimes the Cirrus card will card 0, sometimes on-board audio.The card number depends on which driver is registered first, whichis purely random.

You can manually assign fixed card (slot/index) numbers usingthe slot option of the snd module. Forexample, if you want the Cirrus card always to be the first andon-board audio the second one, add the following line to your/etc/modprobe.d/cirrus.conf file:

For kernel 4.9 add this line:

Troubleshooting

If something doesn't work as expected please post your questions inthis threadon the element14 site.

In order to track down problems follow the steps below andinclude the URLs to the paste files in your post:

1. Add the following line to /boot/config.txt toenable devicetree debugging, then reboot your RPi.

2. Upload your /boot/config.txt file, theGPU firmware version, GPU firmware and linux kernel logsand the outputs of lsmod and aplay -l.The easiest way to do this is by using the pastebinitcommand which is included in Raspbian. Enter the followingcommands and include the URLs that are output on theterminal in your post:

Cirrus Logic Sound Cards & Media Devices Driver Download For Windows 8.1